@dr3x Hi!
Are you using Arduino IDE v2.1.0?
If so, I consider this a confusing and annoying bug in the application.
The app kindly and incorrectly identifies your board type!
You still need to type in ESP32S3 Dev Module as shown below on my computer!

Screenshot 2023-06-27 at 12.24.32 AM.jpg

Hope this helps, Terry

@basvandepavert Thanks for getting back to me!
Let me know!
-Terry

@m4biz Fantastic news!

You can also put a small
delay(500);
In the loop to keep it from locking up and becoming very hard to upload another sketch!

But: GREAT JOB !

@ivan Hi Ivan, this site is a volunteer user community site and anything I say is simply "advice".
LilyGO make no claim of waterproof, but it seems well sealed.
I think accidental splashing such as washing hands would be OK.
Otherwise I would "Damp-Cloth" it as you say!
-Terry

Great news! Thanks to the efforts of @kreier, a USB VID/PID was able to be secured using a third-party so that official circuitpython support could be added. The T-Display RP2040 now has official CircuitPython support! 🥳

It is a grove connector (!) for I2C external sensors, etc.

@teastain2 thank you so much

@teastain2 Thank you. That was the conclusion I was coming to. Realistically, I can only use i2c, rather than some resistive sensors and use some A2D pins.

I'm using the T-PCIE SIM7600G-H and not having an issue.
By "disconnecting"... is the PCIE disconnecting from the CPU or is it disconnecting from the 4G network?

thanks @teastain2
Yes I'm a newer, thanks for your repository

593dbbb6-32fc-405b-b08c-6e15fe4dd5d6-[]K{OW8J6EUNN%41}7Q{7_I.JPG
RV1 resistor position, as shown in the diagram

@gerald10 said in T-SIM7600G-H R2 questions:

T-SIM7600G-H R2

Hi,

i have the A7608 board, which is quite similar to what you have.

some answers:

I do not know, but it would be best to implement some logic where if the battery is below a threshold you keep deep sleeping. That battery also costs a lot of money. You might want to first try a standard 18650, e.g. with 2-3 Ah and see how it goes. Connecting to wifi every 15 minutes and using proper deep sleep gives me a month of battery time without any charge. I think the open circuit voltage of that panel is to high. The board has a CN3065 charging chip (search the datasheet online), and accept up to 6.5V max. Search a "5V" solar panel. Again, I do not know the specifics of your application, but a 1w solar panel can do miracles in many applications. this will depend on the cpu frequency you set for the esp32. At 240MHz, my board sucks 40 mA, but at 40 or 80 MHz you can go down to 10 mA. For battery powered applications you need to learn to deep sleep as much as possible. not sure not sure, but I would suspect live streaming 24/7 requires a different thinking for the power system not sure the antenna can stay in the enclosure you use for the board i use standard abs or polycarbonate enclosure boxes. There are tons of models available for ~10$

Davide

Is there perhaps a test pad for VBUS?

@kreier Thanks for helping out with this. I saw your PR. Looks like they’re waiting for an update from you. https://github.com/pidcodes/pidcodes.github.com/pull/827#discussion_r1135991673

@hosky well, you could use the esp32 built in ADC to read pin 4 bat volt, or wire the 5V pin to a voltage divider and then to a GPIO, such as 16 and digitalRead it.