T-Display-S3 (touch version) trouble to connect SD card reader (SPI)

[Stefan]

Hi,
I try to connect a SD reader via SPI to the T-Display-S3 touch version - sadly without success.
From reading other comments/websites it seems I can freely define the pins for a secondary (HSPI) SPI bus.
This is what I tried:

#include "FS.h"
#include "SD.h"
#include "SPI.h"

SPIClass spiSD(HSPI);
#define SDSPEED 27000000

// SPI port #2: SD Card Adapter
#define SD_CLK 21 //yellow
#define SD_MISO 18 //brown
#define SD_MOSI 17 //orange
#define SD_CS 16 //green

in setup I have:

Serial.begin(9600);

spiSD.begin(SD_CLK, SD_MISO, SD_MOSI, SD_CS); //SCK,MISO,MOSI,cs

if (!SD.begin(SD_CS, spiSD, SDSPEED)) {
Serial.println("Card Mount Failed!");
return;
} else {
Serial.println("Card Mount Successful!");
}

but all I get is "Card Mount failed" - I have multiple reader modules, but I get the same result with all of them, so i assume the issue is with my setup/pins/code...

any help would be highly appreciated - thanks in advance

[Stefan]

I found the solution on my own with some help of Google.
In the end I only had to add one more line of code to make it work (switching the CS Pin to output...):

pinMode(SD_CS,OUTPUT);

so the complete code-part looks like this:

void setup() {

  Serial.begin(9600);

  spiSD.begin(SD_CLK, SD_MISO, SD_MOSI, SD_CS);  //SCK,MISO,MOSI,cs
  pinMode(SD_CS,OUTPUT);

  if (!SD.begin(SD_CS, spiSD, SDSPEED)) {
    Serial.println("Card Mount Failed!");
    return;
  } else {
    Serial.println("Card Mount Successful!");
  }
}

[eflorea]

Hi Stefan, I was curious if you using the SPI port had any interference with the touch functionality.

I noticed that in the pinout the SPI pins 10-13 are also connected to some of the touch pins ?

I'm still waiting on my device to arrive but I hope there is no issue there.

Thank you.

[teastain2]

@eflorea The "Touch pins" are an ESP32 Espressif use of the pins as analog sensing for a home brew touch interface.
The Touch Screen on the LilyGO T-Display S3 Touch is I2C thus:

https://github.com/Xinyuan-LilyGO/T-Display-S3/blob/main/image/T-DISPLAY-S3-TOUCH.png
So the touch vesion uses up 4 GPIO that the standard model could use GPIO !!!
You should have no trouble.
-Terry

[eflorea]

@teastain2

Thanks for the heads up Terry, I just had my T-Display-S3 Touch delivered on Friday, I will be jumping on it very soon, I need to resolve an issue with the none touch unit....I posted that topic tonight.

Thank you again.

[llsummer]

any thing new for now?
I tested the code above not luck.

[teastain2]

@llsummer What problem are you having?
What exact board do you have?

[llsummer]

@teastain2 said in T-Display-S3 (touch version) trouble to connect SD card reader (SPI):

What exact board do you have?

Thanks.
I have T-Display S3 basic + SD card.
I heard that the Touch version more difficulty to work with SD?

[teastain2]

@llsummer You should have no trouble with either.
Try this official sketch:
https://github.com/Xinyuan-LilyGO/T-Display-S3/tree/main/examples/sd

[llsummer]

@teastain2 Thanks.
not work.

The example/SD just define 3 pins, and I didn't find any where mentioned SD_CS, can be a problem?

I used SD card reader with 6 pins.

[teastain2]

@llsummer

You have to do more self-research. SD on ESP32 is not easy, but it can be done.
There are many many SD memories that cannot be used.

No, I will not elaborate.

[llsummer]

This post is deleted!